Finding Factory Code For Global Link Ultra E Pro Electronic Lock

Question

Question:

We bought a used 2021 geo pro 20bhs with this lock. We do not know the factory or user code. I replaced the battery but need to set a new code. How do I do that without know the previous codes? Is there a factory reset?

asked by: Adam W

0

Expert Reply:

I Googled how to find the factory code for the Global Link Ultra E Pro Electronic Lock for Travel Trailer # 295-000183, and found that you'll simply need to unscrew the back plate. When you do that, there will be a white sticker that says pin code which is the factory code.

expert reply by: Kyle S

0

Answer 1

I attached a link to the instructions for Global Link Ultra E Pro Electronic Lock for Travel Trailer w Keyed Alike Option - Black - Right Hand #295-000183. You can see on the instruction page that it says the following: 1. Press and hold the 9-0 key…

view full answer...

Answer 2

A 235/75-15 tire like what you have would measure right at 29 inches in diameter. So for that we have the CE Smith cover part #CE27440 which would fit and work well for an all black cover. I also attached a link to a page that has all of the spare…

view full answer...

Answer 3

Yes, you can lock the Global Link Ultra E Pro Electronic Lock for Travel Trailers part #295-000183 from the outside without the key. Simply press and hold the 1-2 key and the 3-4 key at the same time on the touchpad. Two descending beeps indicate…

view full answer...

Answer 4

Any time you are towing a trailer that has a fully loaded weigh that is over 50 percent of the vehicle's gross weight, a weight distribution system is recommended. If your vehicle weighs less than 6,000 lbs, a weight distribution system and…

view full answer...

Answer 5

If the tongue weight exceeds the manufacturer stated tongue weight capacity of the vehicle, I'd personally be hesitant about towing the trailer with that particular vehicle. If you do decide to tow the trailer, you'll want to verify the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...