Troubleshooting A Clogged Blow Out Line For An RV Black Tank

Question

Question:

Will this work to unclog my back flush line that the garden hose hooks to to to flush my tank

asked by: Wayne P

0

Expert Reply:

The Valterra Clog Killer Tank Wand System # VAL28VJ is designed to run down the drain for your toilet and spray into the black tank. If you have a clog in a line that you could connect a garden hose to then you would need a blow out plug like # CAM36143. This will allow you to use a compressor to blow the clog out of the line and into the black tank and then you can resume cleaning it with your garden hose.

expert reply by: Kevin C

0

Answer 1

The Valterra Clog Killer Tank Wand System #VAL28VJ is designed to be fed into toilet or drain from the inside. It should not be fed into the black tank from the outside. If you want to clean out the black tank with a hose from the outside you can add…

view full answer...

Answer 2

We don't have a video but the way that the Tornado 360-Degree RV Holding Tank Rinser #CAM40126 works is a lot like how a yard sprinkler works. It uses water pressure from the hose to spin the nozzle around to cover more of the inside of the…

view full answer...

Answer 3

It sounds like you need something like the dual Flush Pro #CAM39062 for rinsing out holding tanks and the sewer hose. But these adapter uses bayonet fittings and hose #LC359724 uses cam-lock fittings. But if you used sewer hose #CAM39761 then with…

view full answer...

Answer 4

The correct Anode Rod is going to be determined by what water heater you have. Unfortunately, your motorhome information does not tell me what water heater you have. The rod that you were looking at, Camco RV Water Heater Anode Rod #CAM11563 works…

view full answer...

Answer 5

Both metals help to protect your tank. There are only a few people that have a preference and it is normally based on aluminium being lower on the Galvanic Scale than magnesium so it produces less driving current between the anode and cathode (tank).…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...