Recommended Oil for A-iPower 2,000-Watt Portable Inverter Generator

Question

Question:

What do YOU recommend oil to buy for the 4stroke iPower 2000watt inverter generator? There’s too many recommendations. Also Can I use synthetic oil? Thx

asked by: Art

0

Expert Reply:

I recommend using SAE 10W-30 APISJ for the # 289-SUA2000i since that is what it was engineered to use according to the manufacturer. This covers a wide temperature range so you probably won't have issues with the viscosity unless it gets really cold. Also yes, you can use synthetic oil with the inverter generator. Full synthetic 5W-30 will actually get you the largest temperature range running from -20°F to 120°F, so if you will be running this in cold temperatures that would be the way to go. If you're looking for what brand to get, I would choose a reputable brand like Mobil 1.

I have included the full recommended oil chart below with ambient temperature ranges for your reference.

expert reply by: Robin H

0

A-iPower 2,000-Watt Portable Inverter Generator Recommended Oil.
(click to enlarge)

Answer 1

The Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 4-1/2 - Galvanized #AKIHUB-545-35-G-EZ-K does not come with the spindle nut. That would come with your axle. For a 3,500 lb axle you would want the Spindle Nut Kit for EZ Lube Axles…

view full answer...

Answer 2

I can help you with greasing up your EZ Lube Axle. First thing I would check would be that the grease is not coming out of the back of the axle through the seal. If this is the case you will need to replace the seal. Our tubes like #L11390 have 14…

view full answer...

Answer 3

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 4

I was able to find everything you need for your 12,000 lb Dexter axles; the electric brakes, oil cap kit, oil seal, bearings, and races. I verified with Dexter that these are indeed the correct parts for your 12k axles. I'll go ahead and list out…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...