Coupler Lock Recommendation for a RAM A-Frame Coupler

Question

Question:

As the subject says, will this work with couplers designed like the Redline Trailer Coupler - CA5400? My coupler pictures included is made by Ram, but the design looks very similar to the Redline coupler.

asked by: David D

1

Helpful Expert Reply:

I have a few trailer coupler locks that will work for your RAM A-frame coupler. I recommend using a coupler lock like the Fastway Universal Coupler Lock, # FA86-0015-307.

This coupler lock is offered with multiple part numbers. Each part number corresponds to a unique key number, so they can also be keyed alike by ordering more than one of the same part number for multiple trailers that you want to use the same key to lock. Check out the video to learn more.

expert reply by: John H

1

click to enlarge

Answer 1

The Camco RV Power Defender, part #CAM55312, can detect a correctly wired circuit, an open ground, reversed polarity, open neutrals, hot/ground wires reversed, and if the wire is hot on neutral with the hot open, as well as if the hot wire is open…

view full answer...

Answer 2

If your RAM brand trailer has a collar-lock style coupler like the Bulldog Coupler #BD028444 yes the EZ Lock Trailer Coupler Lock #BLTL-20-40D would be an excellent choice as a trailer lock. A more universal coupler lock that we offer is the…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference.…

view full answer...

Answer 5

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 7

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 10

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5…

view full answer...

Answer 12

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to…

view full answer...