Replacement Bearings for CE Smith Trailer Hub 13110

Question

Question:

What wheel bearings kits is for a 13110 wheel hub ?

asked by: Justin G

0

Expert Reply:

For your trailer hub with 13110 on it the correct bearing kit would be the part # BK1-100 which comes with L44643 bearings.

expert reply by: Jameson C

0

Answer 1

For mounting a 15" wheel on the CE Smith Trailer Idler Hub Assembly #CE13515 you will want to torque the wheel nuts to either 90-120ft-lbs on a steel wheel or 90-100ft-lbs on an aluminum wheel. I have included our a wheel torque chart below…

view full answer...

Answer 2

Personally, I would install the Dexter Trailer Idler Hub Assembly for 2,000-lb Axles #8-91-05UC1 and add the Washer #SW1000, Spindle Nut #165686, and Cotter Pin #165649 as that's how we usually install them here at etrailer and it makes sense…

view full answer...

Answer 3

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 4

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 9

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a digital…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

We do have 205/75R14 size radial tires that have a load range of D and a speed rating of at least 81 mph. Out of our available selection I recommend going with the Kenda Karrier #AM10235. This tire has a max load rating of 2,200 lbs at 75 psi and a…

view full answer...

Answer 12

Typically, when the outside edges of a tire are showing wear its because the tires are under-inflated. The solution is to inflate the tires to the maximum pressure listed on the sidewall. Now if the outside of tires have what looks like gouges are…

view full answer...

Replacement Bearings for CE Smith Trailer Hub 13110

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching