Can Timbrens for 2003 GMC Sierra 1500 Be Used without Spacer

Question

Question:

Can your Timbren Rear Suspension Enhancement System be used without the round 1inch spacer? Thank you,

asked by: Paul

0

Expert Reply:

The correct Timbren Rear Suspension Enhancement System for a 2003 GMC Sierra 1500 LD is part # TGMRCK15S for extended or regular cab models and part # TGMRCK25S for crew cab models. The springs once installed should be anywhere from 1/2" - 1-1/2" from the contact point. If you would like to decrease the gap then you can remove the spacer from the latter kit which would make the spring not engage as often.

expert reply by: Conner L

0

Answer 1

The Ultra-Fab Dirt Bike Carrier for 2" Hitches #UF48-979033 does not come with an Anti-Rattle Device. I recommend using the Blue Ox Hitch Receiver Immobilizer II - 2" Hitches #BX88224 for the best support and anti-movement device for a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...