Will Gooseneck Ball for GM/Ford also Fit Ram Puck Kit

Question

Question:

Will the curt factory gooseneck ball for a GMC/Chevy/Ford fit in the Ram factory gooseneck? I know the pucks are slightly different. What about the ball fitment?

asked by: Andrew S

0

Expert Reply:

The Ram rail kits are unique so the other gooseneck OEM ball kits would not fit your 2019 Ram 2500 so you'd need to use a kit designed for it like the Curt # C60618.

expert reply by: Jameson C

0

Answer 1

I spoke with my contact at Curt and he had a way for you to release the ball from the underside of the hitch. From underneath of the vehicle the customer will have to remove the cover/plug on the bottom of the ball if there is one. This will reveal…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 5

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the…

view full answer...

Answer 9

Hey Ted, so if you look in the bed of your truck and see 5 holes/pucks that would mean you have the OEM prep. I'd assume if you had it you'd have seen them by now. If you had it you'd only need a ball like the part #C60618. If you…

view full answer...

Answer 10

Hey Don, good question and I checked directly with Air Lift for you and can confirm that so long as your 2024 Ram 2500 Rebel does NOT have the factory auto-leveling air suspension, the air bags you asked about are indeed a fit: - Air Lift LoadLifter…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Will Gooseneck Ball for GM/Ford also Fit Ram Puck Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching