Length and Diameter of Curt MV 600 lb TW Spring Bar

Question

Question:

hello- I lost one of my spring bars for my Weight Dist. hitch. I accidentally forgot it in my dump trailer and its history. Anyway I was wondering what the diameter of the bar and the total length of the bar is? Its the Curt MV 600lb TW bar w/ chains for

asked by: Adam C

0

Expert Reply:

The diameter of the Curt spring bar # C17071 that you referenced is 1-1/2 inches and the length is 30-5/8 inch. Since you have the 600 lb TW MV Curt system this for sure is the correct spring bar and wouldn't require measuring to verify.

expert reply by: Jameson C

0

Answer 1

It's possible that EAZ-Lift spring bars will fit the Curt Replacement MV Weight Distribution Head #C17075, but that's not something we can confirm as it hasn't been tested. With that said it is a bit unlikely, as most of the time brands…

view full answer...

Answer 2

The springs bars are the only difference between the Curt MV Weight Distribution Systems part #C17050 and part #C17051 and these are available separately so you can purchase two of the Replacement Spring Bar part #C17072 and then be set when you are…

view full answer...

Answer 3

All of the Replacement Round Spring Bars for the Fastway e2 Weight Distribution systems, #FA94-02-1099, #FA94-02-0899, and #FA94-02-0699, measure 31-1/2 inches long. The diameter of the bar at the upper end is 1.39 inches, and the inside groove…

view full answer...

Answer 4

Unfortunately, the Replacement Spring Bar for Curt MV Weight Distribution System #C17074 are not going to work with your Pro Series WDS. This is because the head on the two systems are different, therefore the bars wouldn't fit into the head.…

view full answer...

Answer 5

The length of the spring bars on the Curt MV Weight Distribution System - Round Bar - 14,000 lbs GTW, 1,400 lbs TW #C17057 is 30-5/8 inches. These are the same bars, #C17074. We do not have this weight distribution system available without the…

view full answer...

Answer 6

The Blue Ox SwayPro Weight Distribution w/ Sway Control #BXW1006 and the Blue Ox SwayPro Weight Distribution w/ Sway Control #BLU66FR are identical aside from different shanks included in each kit. The #BXW1006 uses a shank that can be adjusted from…

view full answer...

Answer 7

Using spring bars that are overrated for the total tongue weight of your trailer can cause a pretty rough ride but other wise would not actually harm anything. If you notice the rough ride then replacing your spring bars with one that are rated for…

view full answer...

Answer 8

The Curt MV weight distribution system spring bar lengths like the #C17073 are 31.67 inches.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Length and Diameter of Curt MV 600 lb TW Spring Bar

Product Page this Question was Asked From

Continue Researching