What is the Length of the Spring Bars on Curt MV Weight Distribution System

Question

Question:

What is the length of the torsion bars? Do you sell this unit without the hitch that slides into the receiver on the vehicle?

asked by: Fred K

0

Expert Reply:

The length of the spring bars on the Curt MV Weight Distribution System - Round Bar - 14,000 lbs GTW, 1,400 lbs TW # C17057 is 30-5/8 inches. These are the same bars, # C17074. We do not have this weight distribution system available without the shank.

expert reply by: Robin H

0

Answer 1

It's possible that EAZ-Lift spring bars will fit the Curt Replacement MV Weight Distribution Head #C17075, but that's not something we can confirm as it hasn't been tested. With that said it is a bit unlikely, as most of the time brands…

view full answer...

Answer 2

The spring bar part #C17074 that you reference is 30-5/8 inches.

view full answer...

Answer 3

Yes, the replacement Reese weight distribution head part #RP58112 that you referenced does fit the shank part #RP54970 that you also mentioned.

view full answer...

Answer 4

All of the Replacement Round Spring Bars for the Fastway e2 Weight Distribution systems, #FA94-02-1099, #FA94-02-0899, and #FA94-02-0699, measure 31-1/2 inches long. The diameter of the bar at the upper end is 1.39 inches, and the inside groove…

view full answer...

Answer 5

The diameter of the Curt spring bar #C17071 that you referenced is 1-1/2 inches and the length is 30-5/8 inch. Since you have the 600 lb TW MV Curt system this for sure is the correct spring bar and wouldn't require measuring to verify.

view full answer...

Answer 6

When properly set up there is nothing better than the dual-cam sway control systems. The big thing about them is they need to be fine tuned which is going to require setting up the system, taking a test drive, making adjustments, and repeating until…

view full answer...

Answer 7

You are correct, adding a second sway control bar, like the Curt Friction Style Sway Control, #17200, is recommended for trailers over 26 feet long. I might start out conservatively if the sway you are experiencing is not too bad, and order one sway…

view full answer...

Answer 8

We currently do not have the #C17074 spring bar so I cannot get the dimensions you are looking for but I do have the dimensions for a similar bar that could work for you. You can check out part #C17117. This spring bar has a diameter of 1.375 inches…

view full answer...

Answer 9

The Curt MV Weight Distribution System part #C17062 would not be very effective with a 14,000 lb trailer. However, you can make it effective with this weight by upgrading to the Replacement Spring Bar for Curt MV Weight Distribution System part…

view full answer...

Answer 10

We do not recommend mixing different brands of components within a system, whether it be a weight distribution hitch or a 5th wheel hitch set-up. While it may be possible to do so in some instances, since the different manufacturers will not have…

view full answer...

Answer 11

The true towing capacity for your 2015 Ford F-150 can vary greatly depending on what exactly the truck is equipped with, such as its engine size, axle ratio, and the contents of any factory towing package it might have. When looking at the online…

view full answer...

Answer 12

Yes, the lower rated Replacement Spring Bar #C17073 can be used to replace the spring bars on your Curt MV Weight Distribution System #C17063 using the existing head. This will convert the system so that it's tongue weight capacity range is 800…

view full answer...

What is the Length of the Spring Bars on Curt MV Weight Distribution System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching