Recommended 7-Way Connector and Brake Controller for a 2016 Ford F-150 w/ Factory 4-Flat

Question

Question:

I have a four pin currently need to install a 7 pin so I can tow my jayco 17fd. Looking for a complete kit. Also is it easy to install an anti sway trailer hitch. It was recommended to get the setup. I have installed a bumper hitch car stereos with amplifiers so I didn’t think this would be too hard.

asked by: Doug R

0

Expert Reply:

To add a 7-way connector to your 2016 Ford F-150 you will need the the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires item # ETBC7. The kit includes a pre-wired 7- and 4-way trailer connector that mounts easily at the rear of your F-150 with an included bracket.

This kit is designed for use on a vehicle with an existing 4-way flat trailer connector and plugs directly into it. You will then connect the blue wire to the blue wire on your brake controller, connect the black wire to the positive post on your F-150's battery, the white wire to ground, and the yellow wire to your reverse circuit if applicable. This will provide you with the ability to control your trailer's brakes and also provide you with a 12v power wire for you trailer's accessory lights.

I have linked an installation video below.

I have linked a couple of installation videos along with the installation instructions for both the 7-way and the weight distribution system. I recommend watching both to see if these installs are within your skill set.

If you need a brake controller I recommend the Tekonsha Prodigy P3 Trailer Brake Controller item # 90195. This is a proportional brake controller that activates your trailer brakes in proportion to your F-150's braking action.

expert reply by: Jerred H

0

Answer 1

Where to start with your wiring harness depends on what available connectors you have under the bumper of your 2020 Ford F-150 and also what trailer connector you're looking to add on your truck. If your truck already has the square shaped…

view full answer...

Answer 2

I do have a way for you to install a 7-way trailer connector on your 2012 Ford F-150 but the plug in the photo you attached does not have all of the circuits needed for a 7-way trailer connector so there is not one that plugs directly into this.…

view full answer...

Answer 3

Since you already have the 4-way trailer connector on your 2008 Ford F-150 you may only need an adapter, part #37185. This converts the existing 4-way to a 4- and 7-way connector in one. It plugs into your 4-way and then the other wires need to be…

view full answer...

Answer 4

To add a 4- and 7-Way trailer connector to your 1999 Ford Van you will first install a 4-Way such as #118344. Then, with the 4-Way installed you can install #ETBC7 to add a 7-Way and retain the 4-Way. I have included some links that show and explain…

view full answer...

Answer 5

For your 2016 Ford F-150 if your trailer does not have brakes all you would need is the part #37185 as an adapter to convert the 4-way to a 7-way. If you do have trailer brakes you would need the #37185 and the install harness part #22292. If you…

view full answer...

Answer 6

The auxiliary 12-volt wire that runs from the 7-way connection to 7-way trailer plug will supply 12-volt power from the vehicle to the trailer. The 12 -volt power will allow interior or exterior lights to run that are not wired in to the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...