Box Dimensions for Easy Grease Trailer Idler Hub Assembly for 3.5K Axles

Question

Question:

Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized I would like to know the dimension of each box. How many boxes make 4 cubic feet? Thanks. Quisiera saber la dimensión de cada caja. Cuántas cajas hacen 4 pies cúbico? Gracias.

asked by: Angelo G

0

Expert Reply:

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles # AKIHUB-545-35-G-EZ-K will ship in a box that measures 11" x 11" x 6". That makes each box a little less than 1/2 of a cubic foot which means you should be able to comfortably fit 8 boxes in 4 cubic feet of space.

Attached is an installation video for you to check out!

expert reply by: Jon G

0

Answer 1

Karrier and Loadstar are two different brand names used by Kenda. There's no difference in quality or function between the two brand names. For a ST175/80-13 Radial trailer tire in load range D, I'd recommend part #AM10210 if you're…

view full answer...

Answer 2

The speed rating is 81 mph for the Loadstar ST175/80D13 Bias Trailer Tire - Load Range C #AM1ST76, but I definitely do not recommend them for highway use, despite that. The reason for that is they are a bias tire, which means they are very stiff,…

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...