Overall Diameter Of The LaSalle Bristol Coupling # 344633003

Question

Question:

What is the outer diameter of coupling, not the OD of the pipe that goes into it?

asked by: Jim

0

Expert Reply:

The walls of the LaSalle Bristol Coupling for RV Sewer System # 344633003 are 1/4" thick so the overall diameter of the coupler is 4".

expert reply by: Kevin C

0

Answer 1

You should be able to tell which Valterra Double RV Waste Valves you need by inspecting your current connection points. The one end with the lugs on it is the same on all 3 parts so you simply need to determine if you need hubs, spigots, or a…

view full answer...

Answer 2

You should be able to tell which Valterra Double RV Waste Valves you need by inspecting your current connection points. The one end with the lugs on it is the same on all 3 parts so you simply need to determine if you need hubs, spigots, or a…

view full answer...

Answer 3

The LaSalle Bristol Coupling for RV Sewer System #344633003 is designed to fit over a 3 inch pipe so it has a 3 inch inner diameter and the outer diameter is 3.5 inch.

view full answer...

Answer 4

The difference between all three of the part numbers is the difference between a "hub" and a "spigot." The hubs fit over the spigots so it's basically the style of fitting you need. The part #TR38 has a hub and a hub for bot…

view full answer...

Answer 5

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 12

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Overall Diameter Of The LaSalle Bristol Coupling # 344633003

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching