Inner and Outer Diameter of LaSalle Bristol Coupler # 344633003

Question

Question:

If it works with 3inch ABS pipe then the inner diameter must be 3.5inch instead which is the outside diameter of a typical 3inch ABS pipe.

asked by: Rich

0

Expert Reply:

The LaSalle Bristol Coupling for RV Sewer System # 344633003 is designed to fit over a 3 inch pipe so it has a 3 inch inner diameter and the outer diameter is 3.5 inch.

expert reply by: Jameson C

0

Answer 1

If you have two connection points with a 3-1/2" inner diameter and just need something to slip into both of these connections then you would just need standard 3" ABS pipe, which we do not currently offer but you can get at a local…

view full answer...

Answer 2

You should be able to tell which Valterra Double RV Waste Valves you need by inspecting your current connection points. The one end with the lugs on it is the same on all 3 parts so you simply need to determine if you need hubs, spigots, or a…

view full answer...

Answer 3

The difference between these models is the connection points for the black and gray water pipes. A hub will fit over a pipe while a spigot will fit inside of a pipe. You'll just need to choose the correct connection type for your current piping.…

view full answer...

Answer 4

The walls of the LaSalle Bristol Coupling for RV Sewer System #344633003 are 1/4" thick so the overall diameter of the coupler is 4".

view full answer...

Answer 5

The difference between all three of the part numbers is the difference between a "hub" and a "spigot." The hubs fit over the spigots so it's basically the style of fitting you need. The part #TR38 has a hub and a hub for bot…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Inner and Outer Diameter of LaSalle Bristol Coupler # 344633003

Product Page this Question was Asked From

Continue Researching