Do Wheel Masters Tire Pressure Valve Extenders # WM80292 Depress Original Tire Valve at All Times

Question

Question:

Do they have an actuator spring that only depresses the original valve when pressed on, or do they depress the valves all the time? Thanks!

asked by: Movses B

0

Expert Reply:

The Wheel Masters Tire Pressure Valve Extenders # WM80292 do depress the original valve on the tire at all times once they are installed. Their Schrader valve on the extender then becomes the stop-point for the pressure in the tire. This part consists of two extenders with caps.

expert reply by: Adam R

0

Answer 1

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 2

The clearance between the bottom of a 5th wheel overhang and the truck bed is going to depend on several factors including the ride height of the truck, the height setting on the pin box on the trailer and the height setting on the 5th wheel hitch.…

view full answer...

Answer 3

As long as you use valve extenders that are not airless (don't hold air) and are constructed of brass or steel, like the Wheel Masters #WM8005 which do hold air, so they will be compatible with a TireMinder system. TireMinder has a few different…

view full answer...

Answer 4

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 7

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 8

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Answer 9

Hey Keith, we have the Roadmaster Universal Braking Monitor part #RM-9530 which will give you exactly what you are looking for.

view full answer...

Answer 10

Since your Grand Design came with the CRE3000 equalizers you will need three of the MORryde X-Factor Crossmember item #MR33WR. All of the hardware is included. I have linked an installation video below.

view full answer...

Answer 11

We have both the 20,000LB Base #BWRVB3300 and 25,000LB Base #BWRVB3305 which will fit the factory puck system on your 2011 Ford F-450. With you already having the Head #BWRVC3006 this will give you either the 20K #BWRVK3300 or 25K #BWRVK3305…

view full answer...

Answer 12

On single axle trailers typically you put the hanger spacing right at 1/4 of an inch shorter than the leaf spring length from eye to eye center. So if you were using the leaf spring part #e54SR that you referenced which measures 25-1/8 inches long…

view full answer...

Do Wheel Masters Tire Pressure Valve Extenders # WM80292 Depress Original Tire Valve at All Times

Product Page this Question was Asked From

Continue Researching