Does Warn Zeon 12 Winch Fit Bulldog Winch Hitch Mounted Plate

Question

Question:

I have a chevrolet silverado 1500 pickup from 2014. I am looking for a winch installation with a removable brackett containing the Warn Zeon 12, that can be removed from the vehicle. Does the warn zeon 12 fits the bulldog hitch mount?

asked by: Arne E

0

Expert Reply:

It does! I did some research and found out the Warn Zeon 12 winch has the standard 10" x 4.5" bolt pattern, which is exactly what the Bulldog Winch mounting plate has. So yes, the two are compatible, and the part number for the hitch mounting plate is the following:

- Bulldog Winch Hitch Mounted Winch Mounting Plate # BDW20011

expert reply by: Kyle S

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 4

I recommend using a Winch #SW39GR with the Hitch Mount #BDW20011. This way you only need a 2" receiver which is typically already on the rear of most trucks and are available for the front. For your tilt trailer you can weld on a Receiver…

view full answer...

Answer 5

The Superwinch S7500 Trailer Winch #SW1475201 is designed to have more of a "universal" style for mounting and may require some adaption for installation because it does not have a typical mounting pattern. The Superwinch S7500 Trailer…

view full answer...

Answer 6

Yes, the Warn M8000 Winch uses a 10" x 4-1/2" mounting pattern which the Curt Trailer Hitch Electric Winch Mount Plate part #C31010 will accept so they can be used together just fine. The 10" x 4-1/2" mounting pattern is an…

view full answer...

Answer 7

For your enclosed trailer the Bulldog Winch Trailer Winch part #BDW15020 would be a great option for pulling in your drag truck as it has a 4,400 lb capacity and was designed for this type of application. Or if you wanted something that would work a…

view full answer...

Answer 8

The Superwinch Tiger Shark Off-Road Winch #W85NF that you referenced does not require installing an additional fuse as it has one built into it.

view full answer...

Answer 9

Long story short, that's not going to work for you even with a double line pull using a snatch block like the #CU881079. In reality, you need at least 1.5x the GVWR of your vehicle when it comes to winch capacity. The #BDW10044 I mentioned as a…

view full answer...

Answer 10

The Front Runner Slimline II Platform Rack #FR89MJ is the best way to carry a Tent #FR26RV on your 2024 Kia Sportage. The platform will attach to your raised roof rails and will allow you to attach the tent using their Kit #FR99RV.

view full answer...

Does Warn Zeon 12 Winch Fit Bulldog Winch Hitch Mounted Plate

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching