Does the Manual Switch Kit for Pace Edwards Tonneau Cover Require Pushing and Holding

Question

Question:

Hi, can you tell me if the pace Edwards manual switch works with a “press and release” to open or close completely or if it is required to hold the button to keep the topper moving?

asked by: Amanda

0

Expert Reply:

The # 311-BL-1120 is a manual switch. To operate the switch you will have to press and hold it. Releasing it will stop the movement of the cover and it will return to the neutral position. There is no option to press and release for the cover to fully open on close.

expert reply by: Robin H

0

Answer 1

It looks like the interior varies on the 2005 Dodge Ram 1500 depending on what you have exactly. I would recommend mounting the Manual Switch Kit for Pace Edwards BedLocker or UltraGroove Electric Tonneau Cover #311-BL-1120 to the right of the…

view full answer...

Answer 2

The manual switch for the Pace Edwards Bedlocker Retractable Hard Tonneau Cover #PE44CV can be found as part #311-BL-1120 on our site. This plugs into the harness at the canister and then you route and install the switch wherever it works best for…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 9

Hey Robert, for a 5,200 lb Dexter Torflex axle like what you have we have the Dexter lift kit part #K71-724-02 which will give you a lift of 2-7/8 inches.

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 12

Looks like the 2020 Jayco Eagle 355MBQS you are interested in has the max weight possible of 12,300 lbs which your 2017 Ram 2500 Crew Cab Big Horn 4x4 with Cummins diesel could easily tow as it's rated for towing a trailer up to 17,980 lbs.…

view full answer...

Does the Manual Switch Kit for Pace Edwards Tonneau Cover Require Pushing and Holding

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching