What Are The Dimensions Of The Replacement Safety Chain Anchor Kit?

Question

Question:

What are the measurements for these u bolts ?

asked by: Carl K

0

Expert Reply:

I went out to the warehouse and measured the Replacement Safety Chain Anchor Kit for Curt EZr Double Lock Underbed Gooseneck Trailer Hitch # C68WR that you mentioned, and measured 3-7/8" for the longest sections, 3-1/4" across the top, and is 1/2" thick.

Attached is a diagram of # C68WR for you to check out as well.

expert reply by: Bryce D

0

Replacement Safety Chain Anchor Kit U-Bolt Measurement
(click to enlarge)

Answer 1

The inner measurement of the U-bolt is 1-5/8 inches. It is also 2 inches from center to center of the U-Bolt's threaded studs.

view full answer...

Answer 2

Sounds like you are looking for the Replacement U-Bolt Safety Chain Kit #6308. This is the correct replacement U-bolt safety chain kit for Draw Tite Remov-A-Ball hitches.

view full answer...

Answer 3

If the U-Bolt you're needing to replace is part of the bracket kit #C60648 then you'll need to get the whole installation kit unfortunately - I confirmed this with my contact at Curt. The only other U-Bolts used in the Curt EZr Double Lock…

view full answer...

Answer 4

The 2017 Ram trucks with the Cummins diesel have an insanely high towing capacity. The trailer you are considering which weighs 15k dry is about half of what your truck's towing capacity is so it would not be an issue at all. Hitch weight is most…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for a…

view full answer...

What Are The Dimensions Of The Replacement Safety Chain Anchor Kit?

Product Page this Question was Asked From

Continue Researching