Replacement Spring Kit Recommendation for Draw Tite Gooseneck Hitch

Question

Question:

Do you have the spring loaded safty hooks for the draw tite, goos neck kit

asked by: Don F

1

Helpful Expert Reply:

Sounds like you are looking for the Replacement U-Bolt Safety Chain Kit # 6308. This is the correct replacement U-bolt safety chain kit for Draw Tite Remov-A-Ball hitches.

expert reply by: Jameson C

1

Answer 1

If the U-Bolt you're needing to replace is part of the bracket kit #C60648 then you'll need to get the whole installation kit unfortunately - I confirmed this with my contact at Curt. The only other U-Bolts used in the Curt EZr Double Lock…

view full answer...

Answer 2

The inner measurement of the U-bolt is 1-5/8 inches. It is also 2 inches from center to center of the U-Bolt's threaded studs.

view full answer...

Answer 3

The 2017 Ram trucks with the Cummins diesel have an insanely high towing capacity. The trailer you are considering which weighs 15k dry is about half of what your truck's towing capacity is so it would not be an issue at all. Hitch weight is most…

view full answer...

Answer 4

I went out to the warehouse and measured the Replacement Safety Chain Anchor Kit for Curt EZr Double Lock Underbed Gooseneck Trailer Hitch #C68WR that you mentioned, and measured 3-7/8" for the longest sections, 3-1/4" across the top, and…

view full answer...

Answer 5

The Buyers Products Gooseneck Safety Chain U Bolt Kit #337BRB03 has an overall length of 5-5/8 inches and a length of 4-3/4 inches that is below the top of the truck bed. The diameter is .57 inches and the on center measurement is 1-7/8 inches.

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Replacement Spring Kit Recommendation for Draw Tite Gooseneck Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching