What Size Circuit Breaker Is Needed to Install Prodigy P3 Brake Controller on a 2012 GMC Sierra 3500
Question:
what size circuit breaker do i need to install Tekonsha Prodigy P3 Trailer Brake Controlleror on 2012 gmc sierra 3500
asked by: Brian W
Expert Reply:
If you are installing your own wiring for the Prodigy P3 # 90195 on your 2012 GMC Sierra 3500 like our Universal Wiring Kit # ETBC7 then you'll need a 20A Circuit Breaker # PK54220 for that application.
According to my research though you should just be splicing the controller into existing wiring found under the driver's side dash of your pickup. Aside from that you might need to make a few wiring connections under the hood near the fuse box but that wiring should already be ran for you as well.
Attached is a helpful article on installing a brake controller on 2007-2013 GM trucks for you to check out. It goes into a bit more detail and has some pictures to show what you'll be looking for as well.
Products Referenced in This Question
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Circuit Breaker - 20 Amp - Perpendicular Mount Bracket - Cycling Auto Reset - Metal - Type I
- Accessories and Parts
- Wiring
- Circuit Breaker
- 20 Amp
- Pollak
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Brake Controller
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires
- Shop: Trailer Wiring
- Shop: Pollak Circuit Breaker - Cycling/Automatic Reset - 40 Amp - Straight Mount Bracket
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Tekonsha Prodigy P3 Trailer Brake Controller Installation - 2018 Honda Pilot
- Video: Tekonsha Prodigy P3 Trailer Brake Controller Installation - 2020 Hyundai Palisade
- Video: Trailer Brake Controller Installation - 2011 Honda Pilot
- Shop: T-One Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector
- Shop: Jacketed 2 Wire (Brake Wire) - 12 Gauge - per Foot
- Shop: Pollak Circuit Breaker - Cycling/Automatic Reset - 20 Amp - Straight Mount Bracket
- Search Results: 3070~p
- Search Results: wire
- Q&A: How to Install a Brake Controller on a 2017 Honda Pilot
- Search Results: circuit breaker
- Q&A: Towing Capacity and Weight Distribution for 2017 Jeep Wrangler
- Shop: Towing Mirrors
- Search Results: 90250
- Search Results: tekonsha prodigy rf
- Search Results: 7 pin wiring kit
- Video: K-Source Snap and Zap Custom Towing Mirrors Installation - 2009 Jeep Wrangler Unlimited
- Search Results: breaker
- Q&A: Loud Clicking Noise in 2012 Toyota Tundra with Tekonsha Prodigy P3 Brake Controller # 90195
- Q&A: What Size Circuit Breaker is Needed to Install the Prodigy P3 # 90195 on a 1989 Toyota Pickup
- Q&A: Does the Ground Wire On the 7-Way Need to Run to the Battery
- Q&A: Troubleshooting Hybrid Error Code After Trailer Wiring Install of 2010 Toyota Prius
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
on Trailer Brake Controller
