Will Hopkins HM09175 Hitch Level Fit Thumb Latch Coupler

Question

Question:

I have about 2 3/4” from the back of the hitch lever to the front jack mounting bolt. Will this bolt interfere with mounting the level?

asked by: Ron

0

Expert Reply:

Thanks for sending in a picture of your thumb latch coupler and trailer jack. Based on seeing that we know the Hopkins Trailer Hitch Level with Cover part # HM09715 would fit and work great as we had chance to install this on the exact same coupler as you can see in the attached review video.

expert reply by: Jameson C

0

Thumb Latch Coupler
(click to enlarge)

Answer 1

I went out into our warehouse and pulled a Hopkins Trailer Hitch Level #HM09715 and took pictures of the installation instructions. I attached them to this page for you to check out.

view full answer...

Answer 2

The Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 5" Screen Item #FOS05TASF only has a 2 amp 125v slow blow fuse in the power cable. If you take apart the portion of the cord that goes into the 12v outlet…

view full answer...

Answer 3

Thanks for reaching out, i have a couple things for you to do. Let me explain below: *12V PWM Filter for RV Backup Camera Systems - Hardwire #VGR64VR. The newer GMC vehicles use PWM(Pulse With Modulation) in their electrical systems. The Furrion…

view full answer...

Answer 4

You will want to use a cobalt or titanium drill bit when drilling the 5/32-in pilot hole for the #HM09715 hitch level. These type bits are used for harder metal and will do a better job than just a steel or high-speed steel bit as they will dull…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 6

Thanks for sending in a picture of your thumb latch coupler and trailer jack. Based on seeing that we know the Hopkins Trailer Hitch Level with Cover part #HM09715 would fit and work great as we had chance to install this on the exact same coupler…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Sean, We do offer the Ground Control 3.0 for prepped trailers part number 2021106810 as part #LC52ED. This is going to include the rest of the components needed to complete the system. Since we don't have a video of this kit yet…

view full answer...

Answer 9

The Everchill RV Refrigerator w/ Freezer #324-000119 either has a clogged drain line or just needs more space to breathe while operating. If you pull the unit out you can see the drain line by removing the wire grate on the back of the unit and can…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

For your 2015 GMC Sierra 3500 Denali DRW 4x4, I recommend using the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs part #F2709 over the Air Lift LoadLifter 7500 XL Air Helper Springs part #AL57538 for two reasons. The first reason is…

view full answer...

Will Hopkins HM09175 Hitch Level Fit Thumb Latch Coupler

Product Page this Question was Asked From

Continue Researching