Does Hopkins Endurance 5th Wheel/Gooseneck Wiring Fit 2003 & 2013 Ford F-250

Question

Question:

Will the same plug on my 2003 ford f250 work on my 2013 F250? Will this plug work on a 2003-2013 ford f250

asked by: Hans S

0

Expert Reply:

Yes it does; I verified with Hopkins that their Endurance wiring harness will fit both a 2003 and a 2013 Ford F-250. There are actually two of them, one with a 6 foot harness and the other with a 10 foot harness, which you may want depending on where you are going to mount it in your truck bed:

- 6' Harness: Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness with 7-Pole Plug # HM41158

- 10' Harness: Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness with 7-Pole Plug # 41157

expert reply by: Kyle S

0

Answer 1

The CargoGlide 2200XL Sliding Tray for Trucks - 2,200 lbs - Steel Frame - 8" Rail #CG2200XL-8048 for your 2017 Ford F-250 is 48 inches of usable deck space, but the outside edges of the frame measure 49-1/4 inches from side to side. I…

view full answer...

Answer 2

Yes, the CargoGlide 2200XL Sliding Tray for Trucks #CG2200XL-8048 will fit your 2022 Ford F-250 6-3/4' bed. This sliding cargo tray has a maximum capacity of 2,200-lbs. and also has integrated anchor tie-downs, that have a 400-lb capacity at…

view full answer...

Answer 3

Yes, the turnbuckle part #TB38 is one of the turnbuckles that comes with the kit part #TDHP which has a 3,000 lb capacity as a set. The 3,000 lbs would be a safe working load limit and not the break strength capacity which Brophy does not list.

view full answer...

Answer 4

The Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness w/ 7-Pole Connector - 6' Long #HM41158 will work on your 2015 Ford F-250 Super Duty, but depending on where you want to mount it may be a little short. If you want a longer…

view full answer...

Answer 5

Yes, the Hopkins 5th Wheel 7-Way Wiring Kit part #HM41158 does fit your 2003 Ford F-250 and will work great. This plugs inline with your current 7-way to give you an additional one to install up in your truck bed.

view full answer...

Answer 6

I recommend using the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness w/ 7-Pole Connector - 6' Long #HM41158. It mounts in the truck bed sidewall, tailgate post or the wheel well. It will plug into your factory wiring.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...