Replacement Bearings for 2001 EZ Loader Adjustable Boat Trailer

Question

Question:

I have a ez load boat trailer vin 1zeaaaka81a110882 model #1ezb14171250nb can you tell what bearings and seals I need

asked by: Leon P

0

Expert Reply:

According to EZ Loader, the correct inner and outer bearing for your boat trailer is # L44649. This uses a 12194TC grease seal but from what we have found in the past, the # 34823 will work as a replacement.

expert reply by: Robin H

0

Answer 1

This seal, #34823, is a compatible cross-reference for the Transcom 12192. Its inner diameter is 1.249 inches and is outer diameter is 1.983 inches. You can measure your hub's inner bore to determine if this seal's outer diameter…

view full answer...

Answer 2

I spoke to my contact at Kodiak and he informed me that he sees this problem a few times a week and it's always because the trailer is an EZ loader or a Tinker trailer that actually has 1.683 spindles instead of 1.72 and that is why the…

view full answer...

Answer 3

I did some research and found that the 12194TC seal you said you have measures 1.250 inside diameter, and 1.979 outside diameter. The seal I recommend is part #34823. The dimensions listed for this seal are 1.249 inside diameter and 1.983 outside…

view full answer...

Answer 4

Your trailer has axles rated for 3,500 lbs. The inner bearing for that trailer is an L68149 and the outer is L44649. Bearing kit #BK2-100 has the correct bearings and races but you would need a different seal, #168233, available separately.

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 8

I checked your order notes and the leaf springs you bought last year were the part #e28SR which are for 5k axles. Since this is over the capacity of your axle failure would not have been caused by over loading the trailer assuming you stayed under…

view full answer...

Answer 9

The Dexter 072-078-00 is a 2,200 lb capacity leaf spring. You can use a higher capacity leaf spring, however it won't increase the capacity of your trailer as the axle is still rated for that max capacity of 4,400 lbs. My recommendation for a…

view full answer...

Answer 10

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Answer 11

I do have an option for you but we have not yet gotten out hands on a 2019 Chevrolet Blazer therefore, have not had the chance to look for the brake controller wiring port either. I checked with both Tekonsha and Curt and it looks like they have not…

view full answer...

Answer 12

The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your Tahoe…

view full answer...