Compatible Weight Distribution Hitch Shank For A Reese WDS That Has More Drop

Question

Question:

I have the reese 49913 setup. With changing trucks the shank that came with setup will not allow me enough to level out camper. I need about 2 more inches. What other shanks are available for this setup?

asked by: Adam L

0

Expert Reply:

We have plenty of options for your Reese Pro Round Bar Weight Distribution w Sway Control # RE44FR!

I recommend taking a look at the:

-Equal-i-zer Weight Distribution Shank # EQ44FR.

This shank has 12" of drop and 15" of rise, which is 3.5" more drop than the shank that came on your Reese WDS system, and is rated for a maximum of 1,400lbs of tongue weight and 14,000lbs of GTW.

expert reply by: Bryce D

0

Answer 1

We can absolutely help you out here, and it makes sense that you'd be getting more sway than you want with an 8,000 lb Fastway system since it isn't rated quite high enough for the 840 lb tongue weight of your loaded 2021 Forest River Vibe.…

view full answer...

Answer 2

The weight distribution shank we offer with the most amount of drop is the Equalizer Weight-Dist Shank part #EQ44FR which offers up to 12" of drop. I have attached a full list of options below if you feel this is too much. That said, measuring…

view full answer...

Answer 3

To get the Curt Assure Brake Controller #C49UR installed in your 2019 Ram 1500 Classic, you will need the Curt Customer Pigtail #C51458. This will plug directly into the port under your dash making install a breeze.

view full answer...

Answer 4

Yes if you wanted to cut off the bottom of the shank of your Reese weight distribution system part #RE94FR that isn't getting used it would have no affect on the higher holes of the shank that are currently being used.

view full answer...

Answer 5

As long as your particular weight distribution shank is not specified as being for Rise-Only or Drop-Only use then it can be used in an inverted position to give you the height adjustment you need to keep your trailer level. For example, Reese Weight…

view full answer...

Answer 6

Yes, you can flip the shank in the weight distribution system #RE44FR upside down in order to get more of a rise. In this position the maximum rise is 8-1/2 inches measured from the top of the hitch receiver opening to the top of the ball platform on…

view full answer...

Answer 7

I went out to the warehouse and pulled the Camco RV Fresh-Water Hose, part #CAM22763, and used the digital calipers to take some measurements for you. The diameter of the hose fitting is 1". (See the image showing these dimensions I made…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...