Does the Tongue Extension Kit for Yakima Rack and Roll Trailer Work With Both the 78" or 66" Trailer

Question

Question:

Can this extension be used on either the 78 inch or the 66 inch rack n roll trailer? Does it include the electrical wiring?

asked by: Lon C

0

Expert Reply:

Yes, the Tongue Extension Kit for Yakima Rack and Roll Trailer # Y08109 will work with either the Yakima Rack and Roll Trailer - 78" # Y08107 or the Yakima Rack and Roll Trailer - 66" # Y08106.

The Tongue Extension Kit for Yakima Rack and Roll Trailer # Y08109 does include the wiring needed for the extension.

expert reply by: Scott S

0

Answer 1

You could probably make one with a fold away hinge but CE Smith does not offer a hitch extender for the CE Smith Multi Sport Boat and Kayak Trailer w/ Bunks #CE48810. Yakima makes tongue extenders for their Rack and Roll trailer #Y08106 with the…

view full answer...

Answer 2

I do recommend adding the Tongue Extension Kit for Yakima Rack and Roll Trailer #Y08109 when carrying boats over 16 feet long with a Yakima Rack N Roll Trailer #Y08107 since it will prevent the boats from contacting the back of your vehicle while…

view full answer...

Answer 3

Yes, we do have the tongue extender. The Tongue Extension Kit for Yakima Rack and Roll Trailer #Y08109 is the correct tongue extender for the Rack n Roll Trailer and will allow you to carry a single 22' boat or two 21' boats.

view full answer...

Answer 4

I checked the install instructions for the Yakima Rack and Roll Trailer part #Y08107 that you referenced and found the following torque figures: Wheel axle nuts (2) – torque to 57 ft. lbs. (77N-m) (a force of 57 lbs. on a 1 ft. lever.) Swingarm nuts…

view full answer...

Answer 5

We have the replacement 2" x 2" Rack and Roll Tongue #8880204 but if you're needing that inner piece on the Tongue Extension Kit #Y08109 then that's only available with the extension kit so you'll need the whole part number.

view full answer...

Answer 6

You could use a hitch extender or a longer ball mount with the Yakima Rack'n'Roll trailer #Y08107. However there are a couple of issues. First, a hitch extender will reduce the tongue weight capacity of the hitch by 50 percent. this may not…

view full answer...

Answer 7

From the ground to the top of the crossbars when the the Yakima Rack and Roll Trailer, #Y08106, is level, it measures 22 inches. The Heavy Duty Shocks, #Y08110, is using the terms shocks as an all encompassing term that covers the shock itself and…

view full answer...

Answer 8

I called Yakima and they gave me the dimensions of the two ends on the Yakima Tongue Extension Kit #Y08109. The end of the extension that slides out of the extension and into the trailer tongue has an outside dimension of 1-1/2 inches. The other end…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...