Replacement Trunnion Spring Bar For Curt Tru Track Weight Distribution System

Question

Question:

I have the 15000 lbs system for my enclosed car trailer ~1300 tw and want to use the same head for my new camper ~900 tw. The 1500 tw lb bars are likely way too stiff for the lighter camper so I was planning on ordering this set of bars, new frame brackets, and a lift tool for the new camper. Just want to make sure they are compatible with the head for the 15000 system as the head angle adjustment system appears to be significantly different between the 15000 and the 10000 systems from Curt.

asked by: Allen

0

Expert Reply:

When it comes to replacement trunnion spring bars for your Curt Tru Track Weight Distribution System The Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System - 1,000 lbs TW # C17536 will work with the original head that you already have.

The Replacement Frame Brackets for Curt TruTrack Weight Distribution System w/ Sway Control # C17508 will work as well and The Replacement Spring Bar Lift Tool for Curt TruTrack Weight Distribution System w/ Sway Control # C17512 will work as well.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

Unfortunately for you and your buddy (since he owes you) that system is no longer made and because of that the replacement spring bars were discontinued. We used to carry the part number as PS58441. The most similar system offered is the Curt MV…

view full answer...

Answer 2

Hey Paul, I spoke with Curt and they stated that the Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System #C17535 would only be compatible with the #C17499. The Curt TruTrack 4P Trailer Mounted Weight Distribution System w/…

view full answer...

Answer 3

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Replacement Trunnion Spring Bar For Curt Tru Track Weight Distribution System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching