Replacement Handles for Ram Jacks

Question

Question:

I have to replace 2 of the crank handles on my Ram 8000# jacks. Top mounted. Where can I buy just the handles?

asked by: Jerry N

0

Expert Reply:

It sounds like you have the RM0708DLJK Ram jacks which are very similar to the # TJD-7000S. You can use the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks # TJD-7000S-HD as a replacement handle for your jacks.

expert reply by: Robin H

0

Answer 1

The Bottom Rail Trim for Enclosed Trailer item #36277-955 you were looking at would work great on your 2005 Pace 12’ enclosed cargo trailer. It can be easily cut to size and is designed for exactly what you are doing. It will cover the unfinished…

view full answer...

Answer 2

The Bottom Rail Trim for Enclosed Trailer item #36277-955 would work great on your 2005 Pace 12’ enclosed cargo trailer. It can be easily cut to size and is designed for exactly what you are doing. It will cover the unfinished edges along the bottom…

view full answer...

Answer 3

We sell a few different shapes and sizes of trailer trim, like the Bottom Rail Trim for Enclosed Trailer #36277-955, so I've attached our page of trim below for you to find the correct size and style needed for your application.

view full answer...

Answer 4

Load range will be different based on the size of your tire, so there isn't a specific load range I can offer, but assuming a trailer with that amount of weight on it has a double axle I can give you some examples. If you had a double axle…

view full answer...

Answer 5

We offer four trailer tires in your required 205/75R15 size and all can be seen on the link provided. The highest-rated tire is part #AM10245 which is a radial tire in Load Range D. This tire is rated for a maximum load of 2,150-lbs at its specified…

view full answer...

Answer 6

That is not a model we carry, so I am unaware of specs for needed wheel. You will need to identify the diameter of the jack tube. We have caster wheels such as the Pro Series 6", Detachable Caster w/ Pin for 2" Diameter Jacks,…

view full answer...

Answer 7

I went to the warehouse and took a measurement of the Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks, part #TJD-7000S-HD. The handle diameter is 1/2-inch. I have attached a photo of the handle with the dimension shown you can check…

view full answer...

Answer 8

You can replace the handle of the Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs #TJD-8000S with the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks - 3K - 7K #TJD-7000S-HD.

view full answer...

Answer 9

I do have several replacement parts available for the RAM Trailer Jack part #TJD-7000S but not an all inclusive rebuild kit. Instead you will need to select from the components listed below and repair the jack as needed. The most common fault on the…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Handles for Ram Jacks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching