Replacement Side Wind Jack Handle for 7000-lbs Square Direct Weld Jack

Question

Question:

I was looking for a handle for the 7000Lb jack part number TJD-8000s weld on jack. the shaft size is just a little over 12mm. Do you carry one

asked by: Dennis A

0

Expert Reply:

You can replace the handle of the Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs # TJD-8000S with the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks - 3K - 7K # TJD-7000S-HD.

expert reply by: Erik B

0

Answer 1

I spoke to my contact at Pacific Rim, they said the correct replacement lower flange bushing and washer for your 8,000 lb Ram jack will be the Replacement Sidewind Handle Shaft Bushing for etrailer and Ram Square, Direct Weld Jacks - 7K…

view full answer...

Answer 2

The Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs #TJD-7000S does not have the replacement screw rod and nut assembly available as a replacement part. You will need to replace the entire jack. I…

view full answer...

Answer 3

I spoke with my contact at EZ-Jack and he says that to use the EZ-Jack on a triple axle trailer you will need to turn the curve up, opposite the wheel, and drive up on the jack and you will be able to change the tires. Other wise a floor jack and…

view full answer...

Answer 4

I went to the warehouse and took a measurement of the Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks, part #TJD-7000S-HD. The handle diameter is 1/2-inch. I have attached a photo of the handle with the dimension shown you can check…

view full answer...

Answer 5

The big difference is the orientation of the foot plate on both jacks. One just has the rectangular shaped foot plate rotated 90 degrees from the other. Aside from that they both have the same capacities and travel.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Answer 10

To keep your back end from squatting, I recommend the Coil SumoSprings Custom Helper Springs for Coil Spring Suspension item #CSS-1094R. These insert into your rear springs and keep your suspension from being pushed down by the weight of your…

view full answer...

Answer 11

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Replacement Side Wind Jack Handle for 7000-lbs Square Direct Weld Jack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching