Replacement Parts Available for the RAM Trailer Jack Part # TJD-7000S

Question

Question:

Is there a repair kit for this and if so is there a drawing or instructions on how to remove and reinstall

asked by: Pat

0

Expert Reply:

I do have several replacement parts available for the RAM Trailer Jack part # TJD-7000S but not an all inclusive rebuild kit. Instead you will need to select from the components listed below and repair the jack as needed. The most common fault on the above trailer jack is the spider gears and in order to replace them you will want to use part # TJD-7000S-GR. The rest of the replacement parts we have for the jack are listed below. If you can identify what is not working on the jack I would be glad to offer a more specific recommendation.

Bearing: part # TJD-7000-BR

End Cap: part # TJD-7000S-CP

Handle: part # TJD-7000S-HD

Drop Leg: part # TJD-7000-FT

Keeper Pin: part # TJD-7000-PN

Grease Zerk: part # GZERK

Handle Shaft Bushing: part # TJD-7000S-BU

I have attached a video that will walk you through the process of rebuilding your RAM trailer jack.

expert reply by: Conner L

0

Aaron D.

1/11/2021

Jimmy, I'm looking for a replacement top cap to the Ram 1200lb Lift Capacity Trailer Jack (1200 series). I'm not sure if top cap is the correct name for the part but it is the cap that covers the gears within in the jack on the end of the metal tube. Not sure if you can help me. Thank you, Aaron St. Dennis

Reply

Jon G.

1/15/2021

The correct replacement top cap that you're looking for is part # TJD-12000-CP. I confirmed this with my contact at Ram jacks.

Reply

Jimmy

9/4/2020

What type of battery is best to use on tongue jack? Deep cycle of cranking battery? Thanks

Reply

Jon G.

9/5/2020

If you're just needing the battery to operate the tongue jack then either one will work just fine. If you plan on using the battery to operate other things on your trailer as well then a deep cycle battery is the way you want to go.

Reply

Answer 1

Yes, because it is a 3-wire light, you can wire the Red Identification Light Bar with White LED Utility Light #OPT88FR to function as rear marker and reverse lights.

view full answer...

Answer 2

I am happy to help you out. We do have the replacement bushing you are asking about for your Square Direct Weld Jack w/ Footplate, #TJD-7000S. That replacement bushing is part #TJD-7000S-BU.

view full answer...

Answer 3

I spoke to my contact at Pacific Rim, they said the correct replacement lower flange bushing and washer for your 8,000 lb Ram jack will be the Replacement Sidewind Handle Shaft Bushing for etrailer and Ram Square, Direct Weld Jacks - 7K…

view full answer...

Answer 4

To repair a Ram Series 12000 jack, like #TJD-12000SP-R2, we have the Gear Kit #TJD-12000-GR or the Replacement Rod and Nut #TJD-12000-RODNUT. Or you could need both. I just depends on what the problem is exactly.

view full answer...

Answer 5

The 8000 Series jack is #TJD-7000S. The replacement gear kit is #TJD-7000S-GR. If you'd like to verify you can measure the gears on your jack. The small gear is 1.331 inches for the outer diameter and 0.505 inches for the inner. Then the large…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Yes, to replace the gears on the 7K etrailer Square Direct Weld Jack w/ Footplate #TJD-8000S you'll need the Replacement Gear Kit #TJD-7000S-GR. Attached is a video showing how to replace gears for you to check out and use as a reference.

view full answer...

Answer 8

Your RAM jack model ej-3550-bbx will use the Replacement Light Switch #EJ-3520-LSW and Replacement Power Switch #EJ-3520-PSW.

view full answer...

Answer 9

The EcoHitch part #EH78VR is the only 2 inch hitch option available for your 2019 Honda Fit and while we haven't had the chance to shoot an install video I did send you a separate email with a PDF of the install instructions. You will need to do…

view full answer...

Answer 10

Your RAM 3550 Jack will use both the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW and the Replacement Light Switch for Electric Trailer Jack with Footplate #EJ-3520-LSW.

view full answer...

Answer 11

Unlike costlier brands of trailer jack the entry-level Pro Series line is not supported with the same repair/replacement parts availability as with the upper tier sister brands like Bulldog and Fulton. The few parts we have available to us are shown…

view full answer...

Answer 12

Since you have a Ram 3,500 lb jack we actually have replacement switches for that jack with the part #EJ-3520-LSW for the light switch or part #EJ-3520-PSW for the up and down function of the switch.

view full answer...

Replacement Parts Available for the RAM Trailer Jack Part # TJD-7000S

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching