Where Will The Receiver Tube Of the B&W Trailer Hitch Receiver # BWHDRH25211 Sit Under The Bumper?
Question:
I’ve recently bought the hitch bwhdrh25211 and it’s looking like when I remove the current hitch There will be a couple inch gap between my bumper and the new hitch. Can you confirm if it will sit tight to the bumper as the factory does? I’d like to keep it the same height so I don’t have to adjust every hitch that I have or buy new ones. Or is it possibly to exchange for a hitch that does?
asked by: Robert B
Expert Reply:
The B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25211 is designed in a way that it will fit with or without a factory receiver. The multiple mounting points on the side plates will decide where the receiver sits. When you remove your factory receiver you will be able to bolt the cross tube in the upper hole set to have it sit where the factory receiver sits.
Product Page this Question was Asked From
B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class V
- 1600 lbs TW
- 16000 lbs GTW
- 16000 lbs WD GTW
- 2 Inch Hitch
- 1600 lbs WD TW
- Visible Cross Tube
- B and W
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Trailer Hitch
- Video: B and W Trailer Hitch - Custom Fit Hitch - BWHDRH25211 Review
- Q&A: Why Won't The B&W Trailer Hitch Receiver Fit a 2005 Dodge Ram 1500 Short Bed With Factory Receiver?
- Q&A: What Does B&W Hitch BWHDRH25211 Look Like Installed on a 2012 Ram w/Factory Hitch
- Video: Best 2005 Dodge Ram Pickup Hitch Options
- Q&A: Best Trailer Hitch Option for a 2004 Dodge Ram 2500 with Aftermarket Bumper
- Shop: Roof Rack
- Shop: Trailer Wiring
- Search Results: 44649
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Choosing the Right Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 68149
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: etrailer Class III Trailer Hitch Installation - 2024 Subaru Crosstrek
- Shop: Brake Controller
- Q&A: How to Determine if Trailer Axle is Not Aligned and How to Measure to Replace Trailer Axle
- Article: Trailer Wiring Diagrams
- Shop: Fifth Wheel Hitch
- Q&A: Replacement Trailer Grease Seals for Allis 5013 29772
- Search Results: 25580
- Video: Review of Curt Custom Fit Vehicle Wiring - Fifth Wheel and Gooseneck Wiring - C56070
- Search Results: equalizer
- Video: etrailer Magnetic Hitch Receiver Reducer Sleeve Review
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Gooseneck Hitch
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
on Trailer Hitch
