Recommended Camper Tie-Downs And Turnbuckles For A 2006 Toyota Tacoma

Question

Question:

Greetings, I own a 2006 ToyoTaco AccessCab 4.0V6, 6spd manual, TRD Off-Road. I am considering buyimg your products to secure a truck camper in the bed. I have been also considering upgrading my truck to something a little newer and before I do I tought I might ask what the model year range is for that particular product matching my truck? *Your S P E E D Y response is wickedly appreciated.

asked by: Deric

0

Expert Reply:

To mount a truck bed camper to a 2006 Toyota Tacoma you would need the following tie-downs:

For 4WD Models without a board or step underneath the bed and a factory hitch:

TorkLift Custom Frame-Mounted Camper Tie-Downs - Front # TLT2303
TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear # TLT3303

For 2WD Models without a board or step underneath the bed and a factory hitch:

TorkLift Custom Frame-Mounted Camper Tie-Downs - Front # TLT2308
TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear # TLT3303

If you do decide to get a new vehicle we'll just need to know the year/make/model, bed length, whether there's any running boards or steps under the bed of the truck, and if the hitch is factory.

You'll also need some turnbuckles to fully tie-down your camper, for this I recommend the TorkLift AnchorGuard Derringer Turnbuckles for Truck Camper Tie-Downs # TLS9020.

expert reply by: Kevin C

0

Answer 1

If you're needing camper tie downs for your 2014 Toyota Tacoma then there are two different options based on whether your Tacoma is 2WD or 4WD: For 2WD models you'll need the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLT2308 and…

view full answer...

Answer 2

Turnbuckles like theHappiJac Original #LC182898 are more or less universal so you'll be able to use them with the TorkLift Custom Frame-Mounted Camper Tie-Downs #TLT2303.

view full answer...

Answer 3

Currently (July 2020) only the powder coated steel TorkLift Tie-Downs #TL78ZR and #TL23RR for your 2020 Ram 1500 are available. When you can go with aluminum I do recommend it though simply because aluminum doesn't need a special coating to…

view full answer...

Answer 4

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Recommended Camper Tie-Downs And Turnbuckles For A 2006 Toyota Tacoma

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching