Replacement Mounting Hardware Kit for BAKFlip G2 & MX4 Hard Tonneau Covers

Question

Question:

Backflip 226102 I need the hardware kit number for the above listed part

asked by: Clayton

0

Expert Reply:

I think what you are looking for is the Replacement Mounting Hardware Kit for BAKFlip G2 Hard Tonneau Cover, # BAKBK-200KIT. This is for the BakFlip G2 model tonneau cover, # BAK26120 and the BAKFlip MX4, # BAK48329. If your cover is not a G2 model, please let me know.

expert reply by: Michael R

0

Answer 1

I believe you are referring to the rubber rail seal kit. If so the correct replacment rail seals for your BAKFlip F1 Hard Tonneau Cover part #BAK72207RB is the Replacement Rubber Rail Seal Kit for BAKFlip Truck Bed Tonneau Covers part…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...