Is Trailer Breakaway Kit a One-And-Done System

Question

Question:

Once the pin has been pulled out of the switch, can it read and used as if hadn’t been removed in the first place. Or is it a one and done system, meaning a new pin and cable is required to restore to function as designed?

asked by: Mike L

0

Expert Reply:

Good question, but no, a breakaway kit like the Bright Way # 3802311 or Hopkins Engage # 20400 are not one-and-done systems.

You can pull the pin and then reuse the system, and in fact, you'll want to pull the pin when testing one after an install to ensure it activates your brakes.

expert reply by: Kyle S

0

Answer 1

Some different brand names of trailer breakaway kits do originate from a common source, and this is also true for items like jacks, landing gear and steps. There really is not a lot to distinguish one from another, since their component parts are…

view full answer...

Answer 2

The battery that comes with the Bright Way Trailer Breakaway Kit with Switch, 12V, 5-Amp-Hour Battery, and Charger #3802339 is a 12 volt sealed lead-acid battery and these batteries have a life cycle that can vary quite a bit, but typically it has…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

I'm not sure why they include that replacement latch but that is not required for any of the aftermarket hitches or wiring. It is probably something related to the installation of the OEM hitch. The etrailer #e45ZR you referenced is what I would…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

I'm happy to say that there is indeed both a trailer hitch and trailer wiring for your 2024 Chevy Trax. The fits for both parts on your '24 Trax are the following: - Curt Trailer Hitch Receiver #C75VV - Tail Light Converter with 4-Pole Flat…

view full answer...

Answer 11

On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...