Recommended Fender and Fender Marker Light for a 2016 1/2 RPOD 180

Question

Question:

Hello, I need a fender and a fender marker light for a 2016 1/2 RPOD 180.

asked by: Kevin C

0

Expert Reply:

We can most likely help with the needed lights as what we carry is from the same suppliers that the OEM's use. If you can provide a part number that would be helpful, or forward an image of the light showing any visible markings. Same with the fender, while we will not carry RV specific body parts, we do have a selection of fenders available such as the Single Axle Trailer Fender w/ Backing Plate, # HP36VR. If you can provide measurements we can suggest a replacement.

expert reply by: Michael R

0

Answer 1

It sure can! The backing plate on the Single Axle Trailer Fender w/ Backing Plate - Steel - 14" to 15" Wheels - Qty 1 #HP36VR you were looking at measure 12" tall as shown in the included diagram so you will just need to…

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is…

view full answer...

Answer 7

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this…

view full answer...

Answer 8

The closest radial tire size I would have to replace the 4.80-12 bias tire size is the Kenda Karrier S-Trail ST145R12 Radial Trailer Tire #AM10130. The 4.80-12 bias tire is 20.7 inches tall and 4.9 inches wide. The 145R12 radial tire is 21.3 inches…

view full answer...

Answer 9

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 10

The 12 inch tires that we carry are rated for 65 miles per hour. Any faster than that for extended periods and the excessive heat build up will cause tire failure. To get a tire with a higher speed rating you would have to go up in size. That also…

view full answer...

Answer 11

The Kenda 4.80-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range B #AM30590 have a max speed of 65 mph. When trailer tires are not speed rated with a letter, the default is 65 mph max. I've attached an article…

view full answer...

Answer 12

The modern size equivalent of the 20.5x8-10 that you have currently would be the same size tire that is on the #AM3H340 that you referenced, 205/65-10. As long as the bolt pattern of your current hubs are 4 on 4 inch the wheels of this would bolt…

view full answer...