Replacement Grease Seal for Trailer with TieDown 46304 Caliper

Question

Question:

I have tiedown 46304 calipers and wanted replacement seals or kits? Your suggestions please?

asked by: William R

0

Expert Reply:

The 46304 calipers are used on axle capacities between 3,500 and 6,000 lbs so that's not quite enough info to determine what seal you'd need. If you have a 3,500 lb axle you'd need the seal kit part # RG06-050. Now if you have a 5,200-6k axle you'd want the part # GS-2125DL if the spindle has an outer diameter where the seal rides of 2.125 inch. If that dimension is instead 2.25 inch you'd want the # RG06-070.

expert reply by: Jameson C

0

Answer 1

I do have an option for you but we don't offer any replacement brake pads for the Tie Down Engineering (TDE) 46304 Caliper as the company is no longer in business. Therefore, our only option to you would be a full replacement for which I…

view full answer...

Answer 2

The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit you'd want…

view full answer...

Answer 3

I believe you meant a TDE 46245, is that correct? If that's the case, you've got a 3500 lb axle which uses a 10 inch hub/rotor with a 5 on 4-1/2 wheel bolt pattern. You'll want to use the Kodiak #KHR10D hub/rotor as a…

view full answer...

Answer 4

Let's start with the similarities. Both kits are compatible with L44649 and L68149 bearings and a 10-19 grease seal. Both kits are intended for use with a 3500 lb axle. Both are intended for marine applications and use dacromet rotor/hub…

view full answer...

Answer 5

The brake pads included with the Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet and Stainless - 3,500 lbs #K2HR35DS you were looking at are not stainless steel. They can be replaced with the stainless steel version, #K225CPSS…

view full answer...

Answer 6

We have the bearings, grease seal and a spindle that will work with the Kodiak 10" Hub-and-Rotor Assembly #KHR10D. This hub and rotor does come with the races needed, so those aren't required to get separately, but here are the rest of the…

view full answer...

Answer 7

Your TDE 46245 looks to use the Bearings #L68149 and #L44649 which are the common bearings used on most 3,500lb axles. You can check and see if your rotors do have these same bearings used on your axle in case they were changed at some point. These…

view full answer...

Answer 8

I am sure we can help replace all of the brake components but without a brand I can't really help pin point just the hub/rotor. Instead the best we could do is a kit that replaces the hub rotors, the mounting bracket, and the calipers. So you…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

From previous customers we've determined that the Kodiak replacement hub/rotor part #KHR10D that you referenced will work as a replacement for the TDE hubs like the 46245 that you have.

view full answer...

Answer 11

If you are needing to completely remove the spindles on your trailer and replace them with new ones the old ones just need to be cut off. These are welded directly to the axle so you will need to use a torch or saw for this process. When installing…

view full answer...

Answer 12

Sounds like you are talking about the races of your hub, the reason your local store doesn't want to sell you them is because they are pretty difficult to install without damaging the hub. You would want to have them professionally installed. The…

view full answer...

Replacement Grease Seal for Trailer with TieDown 46304 Caliper

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching