Replacement Hardware and Uprights For CE Smith Post-Style Guide-Ons # CE27637

Question

Question:

Can we purchase the hardware only that clamps onto the boat trailer? As we have our own pvc tubes.

asked by: Lee O

0

Expert Reply:

We do offer the Replacement Hardware Kit # CE11452-A and Replacement Upright # CE27605PG for the CE Smith Post-Style Guide-Ons # CE27637.

expert reply by: Bud M

0

Answer 1

I do have an alternative for you since the u-bolts included with the CE Smith Post-Style Guide-Ons #CE27637 will only fit up to a 5-1/4" tall frame. Instead we have the Ark Ezi-Guides Self-Aligning Boat Trailer Loading System. This is superior…

view full answer...

Answer 2

The guide 65” poles/markers on the CE Smith #CE27637 Guide Ons are only meant as markers to show you where the trailer is. While they can endure some pressure in relation to a straight on approach, off angle pressure which can occur with water…

view full answer...

Answer 3

The CE Smith Post-Style Guide-Ons for Boat Trailers - 60" Long - I-Beam Clamps - White - Qty 2 #CE27648 are indeed an outer diameter of 2-3/8 inches. The LED Light Kit for Post-Style Boat Guide-Ons #CE27656A are often paired with this kit.

view full answer...

Answer 4

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Replacement Hardware and Uprights For CE Smith Post-Style Guide-Ons # CE27637

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching