Installation of Redline Pre-Drilled Round Rubber Trailer Bumper

Question

Question:

Got the rubber bumper yesterday they say 5/8inch bolts are required why cannot i use 3/8inch bolts as that is a lot of drilling for the larger bolts

asked by: Dave

0

Expert Reply:

The Rubber Trailer Bumper, # D4-96 comes from the manufacturer with recommended guidelines for best fitment their product. If you choose to alter the installation from recommended that is your choice, but it may not hold up the way it was designed with the improper hardware.

expert reply by: Michael R

0

Answer 1

I can understand not wanting to drill holes in the bumper, but the Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 2-1/16" Wide #D4-96 measures 11 inches on center between the bolt holes, there isn't anything that can be done that…

view full answer...

Answer 2

The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit you'd want the…

view full answer...

Answer 3

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 4

You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…

view full answer...

Answer 5

I have attached a link to our selection of 8 inch trailer hub assemblies that use the common 4 on 4 inch bolt patterns for you to filter through. To choose the correct one you will simply need to remove the current hub on your trailer and check the…

view full answer...

Answer 6

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 7

Actually on brake magnets for trailers either wire can be used as the power or the ground so the colors don't really mean anything. Most likely the magnet manufacturer just put what ever color was most convenient on your trailer.

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Installation of Redline Pre-Drilled Round Rubber Trailer Bumper

Product Page this Question was Asked From

Continue Researching