Is the MaxFan Deluex Model 5100K Compatible with LI Batteries

Question

Question:

Ive read some posts that talk about some MaxFan circuit boards not being compatible with LI battery voltages. Mas this circuit board been updated so that it is compatible with LI battery voltages?

asked by: Gary O

0

Expert Reply:

The MaxxFan Deluxe Roof Vent, Fan and Thermostat, # MA00-05100K is a manual lift, 10 Speed unit that operates from a 12 volt direct current (VDC) power supply. It is irrelevant what supplies the required 12 VDC, be it a converter or a battery of any chemistry type.

expert reply by: Michael R

0

Answer 1

14.2-14.4 volts will not destroy the MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat #MA00-05100K, however anything over 13.8v can cause the fan to shut down on the limit switch.

view full answer...

Answer 2

The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat #MA00-05100K that you referenced runs on 12 volts and draws 5 amps max. If your DC outlet can handle 5 amps then this would work but it would be right at the limit.

view full answer...

Answer 3

The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat #MA00-06200K that you referenced needs a 12 volt power source so you are going to need to get 12 volts from the trailer's battery or circuit breaker panel so that it can operate. While the…

view full answer...

Answer 4

The Ventline VentaDome Trailer Roof Vent part #V2110SP-24 that you referenced is going to fit well in your 14 by 14 inch roof opening. It would be a snug fit like you had with the old vent but it would fit fine as-is.

view full answer...

Answer 5

I walked out to our warehouse and pulled the Ventline Ventadome Trailer Roof Vent, part # V2110SP-24, and had to disassemble the vent to remove to vent cover. To start, open the vent as much as possible. Then hold the knob in place while you loosen…

view full answer...

Answer 6

Actually the lid of the Ventline Ventadome Trailer Roof Vent #V2110SP-24 is galvanized.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...