Best Keyed Alike Trailer Coupler Lock

Question

Question:

I have 4 trailers with the Demco EZ latch coupling like your part number DM14040-81, I know you carry locks for these coupling, can you tell me if you have a locking system that all 4 locks could be keyed the same? I tried the 1/4inch master lock system but was told the locks could not be keyed the same for security purposes. Thank you

asked by: Butch C

0

Expert Reply:

Yes, we do have a lock that is keyed alike that will fit a coupler like the Demco Trailer Coupler item # DM14040-81. It is the Fastway Universal Trailer Coupler Lock item # FA86-0015-318. If you order multiples of the part # FA86-0015-318, they will all have key number 318, part # FA86-0015-313 will have key 313 and so on. This lock fits 1-7/8", 2" and 2-5/16" couplers. I attached a videp below that shows more about this lock.

expert reply by: Jerred H

0

Answer 1

Since the Demco Trailer Coupler #DM14040-81 that you referenced has a lock pin hole with a diameter of 5/16" and a minimum span of 3" for the pin lock, the BOLT Trailer Coupler Lock #BL7025285 that you referenced is compatible. The pin…

view full answer...

Answer 2

The inside width of the Blaylock #BLTL-23 is 3-1/4 inches, as you can see in the photograph I've edited for you. I don't know which website you're referring to, but the information is incorrect.

view full answer...

Answer 3

Thanks for the photo of your trailer coupler. That really helps explain what you are asking about. I spoke with a couple of other Experts and we may have a couple options you can consider. One way to go is to use Loctite Threadlocker 262, part…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 9

The 07100 bearing number you referenced is an older bearing that has the same dimensions as #L44643. If both the inner and outer bearings on your existing trailer are the 07100/ #L44643, and the hub has a 4 on 4 inch bolt pattern, the correct…

view full answer...

Answer 10

Instead of using the Hydraulic Brake Kit #AKFBBRK-35-D which requires using 14"-16" wheels you should use the Dexter Galphorite Free-Backing Hydraulic Trailer Brake Assembly Right #T4423400 and Left #T4423500. These will fit with your…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

The Dexter 8-427 hub is no longer available. Even looking through Dexter's site the only references to it are replacement bearings. You can use a wheel with a larger pilot hole as long as the wheel attaches to the hub using lug nuts and not…

view full answer...