Does Reese Hitch Extender part # RP45292 Require Support Chains

Question

Question:

Do I have to use lateral support safety chains on part# 45292 If I use the 24 in. length with a weight distribution hitch. It would be hanging out 24 in. plus the length of the hitch. Thanks

asked by: Don

0

Expert Reply:

Unlike other hitch extenders you do not need to use any type of support chain with the Reese Titan Hitch Extender part # RP45292. This is true for the 24 inch length or the 34 inch length.

expert reply by: Jameson C

0

Answer 1

The safety chains are not included with the extension but are needed. the recommended saftey chains for this application are the 48 inch Long Safety Chain with 7/16 inch Hooks, 5,000 pounds, item #2118-348-04. By turnbuckles, I am assuming you are…

view full answer...

Answer 2

You are tightening the shackle bolts too much if they are binding up. The shackle bolts do not require a specific torque rating because tightening the shackle bolts too much will squeeze the shackle straps against the leaf springs and the whole…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The first thing you'll need to flat tow your 2015 Chevy Malibu LS is a base plate kit like the Roadmaster part #RM-523178-5 that is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,…

view full answer...

Answer 6

You are on the right track. The only way we have that will allow you to use the Thule T2 Pro Xtr Bike Platform Rack part #TH69TX with the 2.5" receiver tube opening on your truck would be with adapter. For this, I recommend the Brophy Hitch…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 10

The Draw-Tite Front Mount Trailer Hitch Receiver #65076 will fit your 2023 Ford F-350 dually. It features a bolt-on installation and has a 2" receiver. The hitch has a 9,000 lb line pull, 500 lb vertical load, and 5,000 lb gross trailer weight.…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Does Reese Hitch Extender part # RP45292 Require Support Chains

Product Page this Question was Asked From

Continue Researching