What Trailer Hitch Is Recommended For My 2013 Hyundai Veloster Turbo

Question

Question:

Looking to get a tow hitch for my veloster turbo 2013, I want to put a dirt bike rack on the back. Will it support this weight? I believe the bike is around 200 or so pounds plus the carrier

asked by: Kyle C

0

Expert Reply:

When it comes to installing a trailer hitch on your 2013 Hyundai Veloster Turbo The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4 inch # C11254 is confirmed to fit your vehicle. The hitch can tow up to 1,000 pounds and has a tongue weight up to 100 pounds, so you will not be able to haul your 200+ pound dirt bike, but you could tow the dirt bike on a trailer using The Curt Class I Drawbar - 5 inch Rise - 11-9/16 inch Long - 2,000 pounds # C45025 and attaching The 2 inch Hitch Ball - 3/4 inch Diameter x 2-1/8 inch Long Shank - Chrome - 3,500 pounds # C40018. The hitch has a gloss black powder coat finish over a protective base coat which offers superior rust resistance.

I would also recommend The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56153 which has a simple plug and play installation that plugs in behind the driver and passenger side taillights externally. It comes out as a 4 flat connector this wiring will plug into your trailer wiring and make them in unison.

I have attached an installation video below.

expert reply by: Noah E

0

Answer 1

For trailer wiring confirmed to fit your 2013 Hyundai Veloster the Curt kit part #C56153 is the recommended kit that will work well.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

What Trailer Hitch Is Recommended For My 2013 Hyundai Veloster Turbo

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching