To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the tail light assemblies to access this harness.
Once installation is complete, the 4-way connector will be stowed beneath your vehicle, near the trailer hitch. A mounting bracket (sold separately) is recommended to keep the connector secure.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.5 out of 5 stars (10 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.Everything was easy except running the power wire to the front battery and the self-adhesive pad wouldn't stick.(dried out). I used some loctite power grab. Instructions were a little vague too. Wish they had a video like for my Volt.
The hitch and the wiring harness both fit perfect with no modifications necessary. The instructions were very clear and straightforward. I would defiantly recommend this setup.
2/9/17 I had my mechanics put it on for me they said the trailer hitch went on fairly easy but the wire harness was a bear took longer to put the wiring harness on the trailer hitch. Still have to get the wiring harness into the trunk it may take a little time also got high hopes successful future
For the most part a very painless installation. Very clear instructions. Simple connections at the rear of the vehicle. Only problematic thing was running the main power from the front of the car to the back and even that was readily facilitated by the CONDUIT that is on the underside of the Veloster. The tricky part will be the actual positioning of the connection where you attach to the trailer connector. Nothing to do with the design of the system but of the vehicle itself. The center exhaust on the Veloster kind of makes for a very hot hitch for sure!
Plug and play was easy,hardest part was running a power wire from switched ignition feed
My order arrived within 2 day. This product came with the instructions that were very easy to understand and the installation was as simple as the instructions showed . I will order again if I ever need anything else.
Easy install, worked great!
Perfect fit
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.