What Size Wheel Center Hole Will Fit on Trailer Hub 8-219-4UC3

Question

Question:

What is the wheel pilot hole size need for a 8-219 drum? 4.9, 4.77, 4.8???

asked by: Gene

0

Expert Reply:

The pilot hole on a wheel would have to be 4.75 inches or larger. It can be larger because this hub uses lug nuts to secure and center the wheel on the hub (lugcentric). If it just had holes for wheel bolts (hubcentric) then the pilot hole would have to be exact.

expert reply by: Michael H

0

Answer 1

I can point you in the right direction in regards to determining the correct hub and drum for your heavy 14,250 lb trailer, but we would not have any way of identifying the exact hub for your 1995 Trailmax. So there are a number of things you'll…

view full answer...

Answer 2

In regards to trailer wheels, the psi limit is actually from the valve stem not the wheel itself. Therefore, you can use the Goodyear Endurance ST205/75R15 Radial Trailer part #724861519 which is what I recommend if you change out the valve stem for…

view full answer...

Answer 3

If you have valve stems with a metal body like the Americana Metal, Bolt-In Valve Stem part #AM20906 then you will want to use flow-through sensors, the TST TPMS for RVs part #TST-507-FT-6-C. If you have valve stems with a rubber body like the…

view full answer...

Answer 4

In regards to a trailer wheel and tire assembly, the psi rating comes from the trailer tire and valve stem. Therefore, if the psi rating of the valve stem exceeds that of the trailer tire you will not have any issues. The trailer wheel itself does…

view full answer...

Answer 5

There isn't a set amount of torque that you need to tighten the nut of the Americana Metal, Bolt-In Valve Stem #AM20906 basically you'll want to watch the rubber grommet on the inside of the wheel as you tighten it and once it's nice and…

view full answer...

Answer 6

You have some options with the 8-219 for replacement parts. These kits will include new brake hubs, bearings, races, seals, caps and wheel nuts. 1/2" Wheel Studs Grease Cap #8-219-4UC3 1/2" Wheel Studs EZ-Lube Cap #8-219-4UC3-EZ 1/2"…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

What Size Wheel Center Hole Will Fit on Trailer Hub 8-219-4UC3

Product Page this Question was Asked From

Continue Researching