What Are the Dimensions of the Curt Solid Steel 2-Inch Hitch Bar with Raw Finish # D36

Question

Question:

Is the 24inch from end to end or from hitch pin hole to end?

asked by: J L

0

Expert Reply:

My contact at Curt Manufacturing confirmed that the 24-inch specified length of their hot-rolled Solid Steel 2-Inch Hitch Bar with Raw Finish is measured from tip to tip. The center of the 5/8-inch hitch pin hole is 2-1/2 inches from the end.

expert reply by: Adam R

0

Answer 1

The Curt Solid Steel 2 Inch Hitch Bar, #D30, measures 12 inches long and 2 x 2 inches square. From the center of the 5/8 inch hole to the shorter end measures 2-1/2 inches. The distance the other way measures 9-1/2 inches.

view full answer...

Answer 2

The Bulldog Winch Rear Wiring Kit part #BDW20207 is exactly what you are going to need to power even the most heavy duty of winches whether that be on the back of your truck or tongue of your trailer. The set of cables are going to run from either…

view full answer...

Answer 3

I spoke to someone at Bulldog Winch and they said the reason the Anderson 175 amp disconnects can work in the Bulldog Winch Rear Wiring Kit, part #BDW20207, is because a winch is used intermittently. He said while the winch can draw up to 400 amps,…

view full answer...

Answer 4

The wiring kit #BDW20207 that you have referenced would actually work well for you. It is designed for winches ranging in capacity from 5,000 up to 16,500 pounds. There are several ways you can wire up a winch depending on where you are putting it.…

view full answer...

Answer 5

This is a really great question that we debated here not that long ago actually. A lot of people have done it both ways and it seems to be fine for most people to ground through the frame. But on higher drawing winches like what you have it's…

view full answer...

Answer 6

While it most likely would work, the Trailer and Vehicle Electric Winch Wiring Kit #BDW20207 has never been tested on your Badlands 12,000 winch so I could not say with 100 percent certainty if it would work for you. If your winch can be powered with…

view full answer...

Answer 7

Yes, I can guide you through the correct way to power your Warn 4000 lb winch by your vehicles battery. You will need to use the item you selected, Trailer and Vehicle Electric Winch Wiring Kit, part #BDW20207, which uses quick disconnects. You can…

view full answer...

Answer 8

You basically just created a winch wiring kit like the #BDW20207 which is 24 feet of 2 gauge wire just like what you have so what you did was a great route to go. Some might run it to the output pin of the alternator but it's basically all the…

view full answer...

Answer 9

The Curt Solid Steel 2" Hitch Bar #D36 that you referenced has only one hitch pin hole drilled in it like what you see in the attached picture. It's a solid shank as well.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...