AMPLock Trailer Coupler Lock For Demco 2" EZ Latch Couplers

Question

Question:

Hello is this a compatible lock for my pj trailer Demco coupler 2 inch?

asked by: Chris

0

Expert Reply:

As long as your 2" Demco coupler does not have the edge lip like the Demco Cast Head Coupler # DM37ZR then you will be able to use the AMPLock Trailer Coupler Lock for 2" Ball Couplers w/o Lip # AMP54FR.

If your coupler is more like the Demco Trailer Coupler # DM14976-52 with the lip you will need the AMPLock Trailer Coupler Lock for Flat Lip 2" Ball Couplers # AMP64FR

expert reply by: Bud M

0

Answer 1

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for…

view full answer...

Answer 2

The Demco A-Frame Trailer Coupler w/ Jack Hole #DM14793-81 that you referenced is a confirmed fit for a hitch ball with a 2 inch diameter. To couple or uncouple your trailer you will simply lift the eZ-Latch in the upward position. If you were…

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

You are correct. Other than how they are made, the Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K #DM37ZR and the #DM14793-81 have the same ratings and will work the same. There is no pro or con to either, so…

view full answer...

Answer 5

Depedning on what your trailer has we may have what you need. If your trailer has an underslung 2-5/16" ball coupler #AMP56FR is a great option. -If you have a flat lip 2" ball coupler, then the AMPLock Coupler Lock for Flat Lip 2"…

view full answer...

Answer 6

I typically recommend using the etrailer E-Track Backing Plate w/ Hardware - Galvanized Steel - 6" Long x 6" Wide - Qty 1 #e89RR on each end of your E-Track sections #E19148 and one in the middle for added support. With one backing plate on…

view full answer...

Answer 7

You can definitely install the galvanized steel e-track on your trailer that has a galvanized steel floor, as really the only potential issues are when installing e-track on dissimilar metals. So you can absolutely install any of the following…

view full answer...

Answer 8

There are a couple of different ways you can lock the Curt QuickPin No-Latch Trailer Coupler for 2" Ball, either with a standard coupler lock, or you can use a 1/2 inch diameter hitch pin lock, since that is the same size as the pin and clip…

view full answer...

Answer 9

The Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles part #84545UC1-EZ is for a single hub. You may consider the CE Smith Trailer Hub Assembly w/ Carrying Case for 3,500-lb Axles part #CE13511 this is the same type hub with a slightly…

view full answer...

Answer 10

The CE Smith trailer hub assembly part #CE13511 will work for you and yes you could reuse the dust cap you have now that has the rubber plug for access to the zerk fitting. Or you could just cover up the zerk fitting with the included cover as well.

view full answer...

Answer 11

The bolt pattern of a wheel is defined by two numbers: the number of bolt holes and the diameter of the circle (in inches) that they form, measured through the centers of the bolt holes. For example, a 5 on 5-1/2 bolt pattern defines a wheel that has…

view full answer...

AMPLock Trailer Coupler Lock For Demco 2" EZ Latch Couplers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching