Parts Needed to Install a Brake Controller on a 2006 Chevrolet Equinox

Question

Question:

hi, my friend if planning to purchase this brake controller for his 2006 Chevrolet Equinox. we tried to look on your website but only found 2007-2013 Chevrolet Equinox. some model does not have a brake signal on/off switch and some does. do you have any instruction wiring for a 2006 Chevrolet Equinox wiring? the other wiring is easy enough 12V supply, wire going back to the connector, etc the most one we are worried is the brake sensor. if his vehicle does not use an on/off switch, hes thinking of just purchasing it locally and have it installed. Let us know. thanks in advance.

asked by: Reg

0

Expert Reply:

The first thing you will need to install a brake controller in your 2006 Chevy Equinox will be to install a 4-way trailer connector. This will carry the tail light circuits of your trailer. For this you would want a Tow Ready Custom Fit Vehicle Wiring # 118391. I attached installation instructions and an install video that shows how this installs, its a pretty simple install process.

Next you will need to convert this 4-way to a 7-way so that you can install and operate a brake controller. For that you will need a Universal Installation Kit for Brake Controller # ETBC7. The install process will be a little more involved for this portion of the install, but it would not be too difficult. Check out the installation instructions I attached for this product and install video as well.

With both of these products you would be able to install the Tekonsha Primus IQ # TK90160, you will need to use the stoplight circuit fuse in your fuse box to get the brake signal, the fuse you will need is fuse 27. I also attached an FAQ article on installing a brake controller from scratch in a vehicle that you should find informative also.

expert reply by: Jameson C

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 4

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 5

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 6

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

Since your 2024 Toyota Grand Highlander doesn't come with the factory tow package you need the Curt T-Connector Vehicle Wiring Harness #C79VV. The module plugs into that 10-Pin connector you found under the cup holder and then the 4-Way harness…

view full answer...

Answer 11

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 12

Yes! We have both a hitch and wiring for your 2024 Toyota Grand Highlander. Hitch - Curt Trailer Hitch Receiver #C26VV Wiring - #C59236 If you are planning to do any towing, you can add the etrailer Ball Mount Kit #989900 to round out a tow package.

view full answer...

Parts Needed to Install a Brake Controller on a 2006 Chevrolet Equinox

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching