Camper Tie-Downs For A 2020 Ram 3500 Dually With An 8' Bed

Question

Question:

Which Tie-downs are needed for a camper for 2020 Ram 3500 Dually 8 foot bed. And which Frame mounts are needed for an 8 Foot bed dually. Thanks

asked by: Nick C

0

Expert Reply:

For your 2020 Ram 3500, you can use the Torklift Custom Frame-Mounted Camper Tie-Downs # TLD2140 for the front, and # TLD3112 for the rear.

expert reply by: Bryce D

0

Answer 1

For your 2020 Ram 3500 dually the correct Torklift tie downs are the part #TLD2142 and #TLD3112. You may also need the part #TLA7004 and to determine that you'd need to measure from front of camper slide in point to rear anchor point; kit is…

view full answer...

Answer 2

The correct TorkLift Custom Frame-Mounted Camper Tie-Downs for a 2020 Ram 3500 with factory hitch and 8' bed is part #TLD3112 for the rear and part #TLD2140 for the front. This is a direct bolt-on fit option with no drilling required. In order to…

view full answer...

Answer 3

I have a solution for you, but the HappiJac FT-UT9 is designed for older model Dodge and Ford trucks, so they're not the correct tie downs. Additionally, there is not a HappiJac tie down that we have available for your 2020 Ram 3500 dually long…

view full answer...

Answer 4

I can tell you some quick measurements to take to determine if the Brophy Clamp On Camper Tie-Downs #HSBP will fit your 2006 Dodge Ram, but these are universal tie-downs and there is not an application guide specific to your truck. That said, it is…

view full answer...

Answer 5

For your 2020 Ram 3500 Crew Cab Dually With an 8 Foot Bed - with board or step extending under bed and with a factory installed hitch you'll need the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLD2142 for the front. If you end up…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 8

Hey James, The correct rear camper tie-downs to go along with your new TorkLift SuperHitch Original Trailer Hitch Receiver #TLD1102 are going to be part #TLR3505. These will mount directly to the hitch at the end of the crosstube.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 11

The height of the B&W Companion OEM 5th Wheel Hitch for Ram Towing Prep Package #BWRVK3600 would be from the bed to the top of the hitch plate. This is to meet up with the pin box on the fifth wheel so that it rides level while you tow for better…

view full answer...

Answer 12

You can definitely install the HappiJac tie-downs in the front and use Torklift tie-downs for the rear, but you'll have to purchase the whole Happijac kit #LC236326-205221 since we don't currently offer the front separately. For the rear…

view full answer...