Replacement Electric Motor For Landing Gear 1-065-041012-01

Question

Question:

Hi, I currently have part # 1-065-041012-01 motors mounted horizontally on my jacks. Will LG-196308 or LC141893 be a better replacement? My motors are mounted horizontally as a reminder. I am not overly concerned about rpm’s and having a faster motor, just want good, reliable replacements.

asked by: Dusti H

0

Expert Reply:

Per conversation with Lippert, the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor # LC141893 is a compatible replacement for the 1-065-041012-01 electric motor you listed.

expert reply by: Michael R

0

Answer 1

Yes you can just purchase the motor, in this case for your Lippert Model 1-065-041012-01, would be the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893. This motor has a maximum load capacity of 5,000lbs and is rated…

view full answer...

Answer 2

I reached out to my contact at Lippert and since your landing gear motor is blowing a fuse as soon as it sees load he mentioned the issue is more than likely that the motor is not getting the correct voltage, with the less common cause being the…

view full answer...

Answer 3

I reached out to my contact at Lippert who said that replacing the motor alone with a Lippert motor like part #LG-142178 or #LC141893 wouldn't work but if you replaced your Atwood gearbox with the Replacement Gearbox #LC276602 then you can…

view full answer...

Answer 4

I recommend the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893 for your 2017 Keystone Carbon 327 5th Wheel Toy hauler. This motor is rated for 5,000lbs of capacity and turns at 7,140 RPM's. The Lippert 5th Wheel…

view full answer...

Answer 5

The Lippert replacement motor part #LC141893 would work as a replacement for what you have and has a higher RPM rating of 7,140 which would be faster than what you have.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

Hi Mark; thanks for the question and I have some good news for you as we have the exact 5th wheel to gooseneck adapter to replace the Turning Point pin box on your Jayco Eagle HT 30.5 CKTS. The correct part is the following: - Gen-Y Hitch Shock…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...