Do I Need to Unscrew the Winch Bolt from the Strap of My DK2 Summit K2SUSP8826?

Question

Question:

Does the threaded pin holding the winch strap have to be unscrewed or can I just thread a bolt on and pull it out?

asked by: Steve L

1

Helpful Expert Reply:

The threaded pin needs to be unscrewed in order to remove the Replacement Winch Strap for Detail K2 Snowplows # K2WS8020 on your Summit K2SUSP8826.

expert reply by: Bob C

1

Answer 1

We don't have a video that details how to replace the strap of your K2 Winch like part #K2RASP8219, but I did speak to my contact at K2 and he gave me a brief description of the process. On the winch there is a u-bolt that needs to get removed…

view full answer...

Answer 2

Do you have a photo of the spool and what screws/bolts hold it together?

view full answer...

Answer 3

You will want to use the Replacement Winch Strap for Detail K2 Snowplows #K2WS8020. This strap is rated for the weight of your Detail K2 Snowplow #K2AVAL8826. The working load is 1,500lbs with a break strength of 3,000lbs. The Replacement Strap for…

view full answer...

Answer 4

The black wire of the #K2WR100 does run to the negative post of the battery. I attached a picture that shows how it wires up. The picture might look a bit different since it's an older model but the wiring is the same.

view full answer...

Answer 5

We really have to recommend you stick with the Snowbear winch strap like part #SB263-323 since it's designed for your brand of winch. I wish I could say the K2 part #K2WS8020 would be a safe option, but since it has a lower capacity and is…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The Rhino Rack ROC25 part #RR46XR has a 165 lb dynamic weight capacity which means that's how much it can carry while travelling and incurring the standard bumps and movement that creates. While Rhino Rack doesn't give a static weight…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...