Do the # TC2319 Tire Chains Fit My 235/60-18 Tires on My 2021 Chrysler Pacifica Hybrid?

Question

Question:

I just purchased two pairs of the titan 2319 chains to go on a 2021 Chrysler Pacifica Hybrid w size 235/60/18...will these fit?

asked by: Jennifer C

0

Expert Reply:

While the Titan Chains # TC2319 fit a 235/60-18 tire size on your 2021 Chrysler Pacifica Hybrid, it is important that you have the required wheel well clearance on your vehicle to safely use the chains. This is important because if you do not have enough clearance, this can cause damage to components in your wheel wells. With the # TC2319, you need a minimum of 1.46" (37 mm) between the top of the tire tread and the wheel well and at least 0.59" (15 mm) between the tire's sidewall and the vehicle itself. I went ahead and attached a diagram that shows how you can make this measurement.

As with all tire chains, I recommend consulting with your vehicle's owner's manual to make sure you abide by all guidelines outlined by the manufacturer.

expert reply by: Bob C

0

Wheel Well Clearance Requirements for the Titan Chains # TC2319
(click to enlarge)

Answer 1

According to the online owner's manual for your 2021 Chrysler Pacifica you will only install the Titan Chain Alloy Snow Tire Chains #TC2319 on the front set of tires. Since that is specifically noted in the manual I wouldn't install…

view full answer...

Answer 2

There are snow tire chains that will work for your 2018 Chrysler Pacifica, though you never did mention the size of your tires. Assuming you have either 235/60-18 OR 235/65-17 I recommend the Titan Chain Alloy Snow Tire Chains #TC2319 because they…

view full answer...

Answer 3

You found the exact tire chain you need for your Lexus RX 450h with 235/60R18 tires, as the Titan chains you mentioned will indeed fit: - Titan Chain Alloy Snow Tire Chains #TC2319 The #TC2319 are a fit for your Continental tires and have the Class S…

view full answer...

Answer 4

For your 2013 Lexus RX 450H that has the tire size of 235-60-18 your best option would be the Titan chains part #TC2319 which are a great value, are easy to install, and will provide excellent traction.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I have spoken with Lippert about the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817 in they past and they informed me that the most important aspect is that the battery/batteries are sufficiently charged, between 12.4…

view full answer...

Answer 7

The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit you'd want the…

view full answer...

Answer 8

I have attached a link to our selection of 8 inch trailer hub assemblies that use the common 4 on 4 inch bolt patterns for you to filter through. To choose the correct one you will simply need to remove the current hub on your trailer and check the…

view full answer...

Answer 9

You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…

view full answer...

Answer 10

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 11

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 12

The 3-1/4 inch diameter hole to install the part #RR5K is the correct dimension to use. We actually even had a customer come back and say they did it with a 3 inch hole saw. I attached a link to the install video you mentioned as well.

view full answer...