What Coating is on TruRyde Grease Seal 10-36 # RH06-070

Question

Question:

What is the coating on the outer surface of the seal?

asked by: Hap

0

Expert Reply:

I spoke with my contact at TruRyde and the Grease Seals 10-36 # RG06-070 that you referenced are packaged in an oil lined sleeve which is the darker color that you see in the picture on the product page. This oil is used to preserve the rubber seal from drying out.

expert reply by: Lori W

0

Answer 1

The seal you're looking for is the Grease Seal - Double Lip - 2.250" ID - 3.376" OD - GS-2250DL #GS-2250DL; the TRP is just the manufacturer of that particular seal, which is Tru-Ryde Products, the manufacturer of the part…

view full answer...

Answer 2

To replace your Dexter 10-36 grease seals I recommend using Grease Seal #GS-2250DL. This seal has an inner diameter of 2.25" and outer diameter of 3.376". This is a double lip seal.

view full answer...

Answer 3

You can definitely use the MORryde suspension bolts if that's what you're wanting to use. The correct kit depends on what your trailer is currently equipped with and how long your shackle straps are (see attached photo of where to…

view full answer...

Answer 4

Yes, the Grease Seals 10-36 part #RG06-070 are a direct replacement for the Dexter 010-036-00.

view full answer...

Answer 5

It sounds like the 6K might be referring to 6,000 pounds although I cannot be 100 percent sure on that. I could tell you for sure if you could tell me the inner and outer bearing numbers stamped in to the bearings. A 7K axle will use inner bearing…

view full answer...

Answer 6

In order to get the correct replacement seal you will want to remove the seal from your hub and get the number stamped on it. If you can't find the number you can also use the dimensions of your seal to get the correct replacement. Get the outer…

view full answer...

Answer 7

It took a bit of cross-referencing, but I found that the 10-10 grease seal, part #RG06-090 is the correct replacement for the Al-KO 568862 seals. You can confirm this by checking the ID of the hub bore where the seal would sit. The ID should be about…

view full answer...

Answer 8

You can use the other components you remove from your hubs. After you have removed the hub components you will want to inspect all of the parts and replace if you find any discoloration or signs of wear or damage such as a nick. On the race you can…

view full answer...

Answer 9

I found a bearing and seals that will fit your Lippert Axles. According to the manufacturer on the 5,200 lbs axles, the outer bearing number is #LM67048, the inner bearing is #25580 and the grease seal will be 10-36, #RG06-070. Now, before you order…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

What Coating is on TruRyde Grease Seal 10-36 # RH06-070

Product Page this Question was Asked From

Continue Researching